Bosch vrm manual

Bosch vrm manual

Bosch NDC-255-P Installation And Operation Manual Ip dome camera 200 series. O connector Audio bosch vrm manual Mounting Camera set-up 3. Page 4: Table Of Contents Display Stamping Web Interface 6. Page 5: Table Of Contents 7.

8 Audio communication Recordings page 7. Table of Contents IP Camera 200 Series Troubleshooting Resolving problems Customer service Maintenance Repairs 9. 1 Transfer and disposal Technical Data 10. Page 7: Safety, Safety Precautions If not avoided, this could result in minor or moderate bodily injury.

Low risk: Indicates a potentially hazardous situation. If not avoided, this could result in property damage or risk of damage to the device. Page 8: Important Safety Instructions 10. Any change or modification of the equipment, not expressly approved by Bosch, could void the warranty or, in the case of an authorization agreement, authority to operate the equipment.

Page 9 Federal Communications Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U. Government Printing Office, Washington, DC 20402, Stock No. How to Identify and Resolve Radio-TV Interference Problems. Cette brochure est disponible aupr├Ęs du U. EC More information For more information please contact the nearest Bosch Security Systems location or visit www. Page 12: Copyrights Digital Equipment Corporation not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.

This software is based in part on the work of the Independent JPEG Group. Page 13: Introduction, Features It uses H. 264 compression technology to give clear images reducing bandwidth and storage. The camera can be used as a stand-alone video surveillance system with no additional equipment or it can easily integrate with the Bosch Divar 700 Series recorders.

Page 14: Unpacking Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. The camera module is a sensitive device and must be handled carefully. Remove the dome from the base. Remove the inner liner by pulling it off the base. Page 16: Microsdhc Card Figure 3. 1 MicroSDHC card Disassemble the camera.

Slide the microSDHC card into the slot. Page 17: Power Connection, Dc Power Connection 120 VAC power supply outlet. When power is supplied to the camera the LED on the bottom- front of the camera lights. This LED can be disabled in the Installer Options menu. Connector Use a shielded UTP Category 5e cable with RJ45 connectors. Connector Relay output switching capability: Max. Alarm input configurable as active low or active high.

5 Audio connectors Connect audio devices to the Line In and Line Out connectors. Page 21: Mounting Attach the camera and base unit securly to the surface using the two supplied M4 screws. Page 22: Camera Set-up, Camera Positioning Do not expose them to direct sunlight or bright spotlights in operating and non-operating conditions. Avoid bright lights in the field of view of the camera.

Page 25: Resetting The Camera, Closing The Unit Align the LED light guide of the dome with the opening at the front of the mounting base and slot it home. Use the supplied special screwdriver bit to tighten the two tamper-resistant screws. The default address pre-set at the factory is 192. Enter the IP address of the camera as the URL. Page 27: Password Protection In Camera, Protected Network If the connection is not established, the maximum number of possible connections may already have been reached.

1 Password protection in camera A camera offers the option of limiting access across various authorization levels. Page 28: Connection Established, Livepage, Recordings, Settings Refer to Section 7. 2 Recordings page, page 90 for more information. 3 SETTINGS Click SETTINGS in the application title bar to configure the camera and the application interface. Page 29 Section 6 Advanced Mode, page 35 for more information on advanced settings. Note: It is recommended that only expert users or system administrators use the Advanced Mode. Special characters are not supported by the internal recording management system.

Page 31: Device Access, Camera Name, Password Define and change a separate password for each level while logged in as service or if the device is not protected by a password. Enter the password for the selected level. Click Sync to PC to apply the system time from your computer to the device. Page 33: Network On to activate the automatic acceptance of DHCP-assigned IP addresses.


Comments are closed.